Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - solarwasser

Pages: [1]
1
YateBTS / Re: LimeSDR and YateBTS
« on: June 17, 2020, 09:54:38 AM »
Hi,
I have the same problem:

uhd_find_devices and SoapySDRUtil --probe=“driver=lime” does find the device but when I start yatebts it doesn't.
I selected transceiver-uhd as transceiver... Anyone here who got yate & limesdr working together?

######################################################
##     Soapy SDR -- the SDR abstraction library     ##
######################################################

Probe device “driver=lime”
[INFO] Make connection: 'LimeSDR Mini [USB 3.0] 1D537DA8A266E1'
[INFO] Reference clock 40.00 MHz
[INFO] Device name: LimeSDR-Mini
[INFO] Reference: 40 MHz
[INFO] LMS7002M register cache: Disabled

----------------------------------------------------
-- Device identification
----------------------------------------------------
  driver=FT601
  hardware=LimeSDR-Mini
  boardSerialNumber=0xa8a266e1
  firmwareVersion=6
  gatewareVersion=1.30
  hardwareVersion=2
  protocolVersion=1

----------------------------------------------------
-- Peripheral summary
----------------------------------------------------
  Channels: 1 Rx, 1 Tx
  Timestamps: YES
  Sensors: clock_locked, lms7_temp
     * clock_locked (Clock Locked): true
        CGEN clock is locked, good VCO selection.
     * lms7_temp (LMS7 Temperature): 50.257133 C
        The temperature of the LMS7002M in degrees C.
  Registers: BBIC
  Other Settings:
     * SAVE_CONFIG - Save LMS settings to file
       [key=SAVE_CONFIG, type=string]
     * LOAD_CONFIG - Load LMS settings from file
       [key=LOAD_CONFIG, type=string]
     * OVERSAMPLING - oversampling ratio (0 - auto)
       [key=OVERSAMPLING, type=int, options=(0, 1, 2, 4, 8, 16, 32)]
  GPIOs: MAIN

----------------------------------------------------
-- RX Channel 0
----------------------------------------------------
  Full-duplex: YES
  Supports AGC: NO
  Stream formats: CF32, CS12, CS16
  Native format: CS16 [full-scale=32767]
  Stream args:
     * Buffer Length - The buffer transfer size over the link.
       [key=bufferLength, units=samples, default=0, type=int]
     * Link Format - The format of the samples over the link.
       [key=linkFormat, default=CS16, type=string, options=(CS16, CS12)]
     * Skip Calibration - Skip automatic activation calibration.
       [key=skipCal, default=false, type=bool]
     * align phase - Attempt to align phase of Rx channels.
       [key=alignPhase, default=false, type=bool]
  Antennas: NONE, LNAH, LNAL_NC, LNAW, Auto
  Corrections: DC removal, DC offset, IQ balance
  Full gain range: [-12, 61] dB
    TIA gain range: [0, 12] dB
    LNA gain range: [0, 30] dB
    PGA gain range: [-12, 19] dB
  Full freq range: [0, 3800] MHz
    RF freq range: [30, 3800] MHz
    BB freq range: [-7.68, 7.68] MHz
  Tune args:
     * LO Offset - Tune the LO with an offset and compensate with the baseband CORDIC.
       [key=OFFSET, units=Hz, default=0.0, type=float, range=[-7.68e+06, 7.68e+06]]
     * BB - Specify a specific value for this component or IGNORE to skip tuning it.
       [key=BB, units=Hz, default=DEFAULT, type=float, range=[-7.68e+06, 7.68e+06], options=(DEFAULT, IGNORE)]
  Sample rates: [0.1, 65] MSps
  Filter bandwidths: [1.4001, 130] MHz
  Sensors: lo_locked
     * lo_locked (LO Locked): true
        LO synthesizer is locked, good VCO selection.
  Other Settings:
     * TSP_CONST - Digital DC test signal level in LMS7002M TSP chain.
       [key=TSP_CONST, default=16383, type=int, range=[0, 32767]]
     * CALIBRATE -  DC/IQ calibration bandwidth
       [key=CALIBRATE, type=float, range=[2.5e+06, 1.2e+08]]
     * ENABLE_GFIR_LPF - LPF bandwidth (must be set after sample rate)
       [key=ENABLE_GFIR_LPF, type=float]
     * TSG_NCO - Enable NCO test signal
       [key=TSG_NCO, default=4, type=int, options=(-1, 4, 8)]

----------------------------------------------------
-- TX Channel 0
----------------------------------------------------
  Full-duplex: YES
  Supports AGC: NO
  Stream formats: CF32, CS12, CS16
  Native format: CS16 [full-scale=32767]
  Stream args:
     * Buffer Length - The buffer transfer size over the link.
       [key=bufferLength, units=samples, default=0, type=int]
     * Link Format - The format of the samples over the link.
       [key=linkFormat, default=CS16, type=string, options=(CS16, CS12)]
     * Skip Calibration - Skip automatic activation calibration.
       [key=skipCal, default=false, type=bool]
     * align phase - Attempt to align phase of Rx channels.
       [key=alignPhase, default=false, type=bool]
  Antennas: NONE, BAND1, BAND2, Auto
  Corrections: DC offset, IQ balance
  Full gain range: [-12, 64] dB
    PAD gain range: [0, 52] dB
    IAMP gain range: [-12, 12] dB
  Full freq range: [0, 3800] MHz
    RF freq range: [30, 3800] MHz
    BB freq range: [-7.68, 7.68] MHz
  Tune args:
     * LO Offset - Tune the LO with an offset and compensate with the baseband CORDIC.
       [key=OFFSET, units=Hz, default=0.0, type=float, range=[-7.68e+06, 7.68e+06]]
     * BB - Specify a specific value for this component or IGNORE to skip tuning it.
       [key=BB, units=Hz, default=DEFAULT, type=float, range=[-7.68e+06, 7.68e+06], options=(DEFAULT, IGNORE)]
  Sample rates: [0.1, 65] MSps
  Filter bandwidths: [5, 40], [50, 130] MHz
  Sensors: lo_locked
     * lo_locked (LO Locked): false
        LO synthesizer is locked, good VCO selection.
  Other Settings:
     * TSP_CONST - Digital DC test signal level in LMS7002M TSP chain.
       [key=TSP_CONST, default=16383, type=int, range=[0, 32767]]
     * CALIBRATE -  DC/IQ calibration bandwidth
       [key=CALIBRATE, type=float, range=[2.5e+06, 1.2e+08]]
     * ENABLE_GFIR_LPF - LPF bandwidth (must be set after sample rate)
       [key=ENABLE_GFIR_LPF, type=float]
     * TSG_NCO - Enable NCO test signal
       [key=TSG_NCO, default=4, type=int, options=(-1, 4, 8)]



Pages: [1]