Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - andrew77

Pages: [1]
1
YateBTS / Solved gsmtrx:ALL ARFCN[0]: Slot ... Excessive TOA errors
« on: September 05, 2016, 12:05:37 PM »
Hello
this is not the first time I install yatebts,
but with the following configuration:
bladeRF> version

  bladeRF-cli version:        1.4.0-2016.06-1-ppatrusty
  libbladeRF version:         1.7.2-2016.06-1-ppatrusty

  Firmware version:           1.9.0
  FPGA version:               0.6.0

libusb 1.0.17
uname -a : 4.4.0-36-generic #55~14.04.1-Ubuntu
and yate -V
Yate 5.5.1 devel1 r6131
 I get always gsmtrx:ALL ARFCN[0]: Slot ... Excessive TOA errors, as a consequence I can't make calls, sometimes shutdown yatebts, etc...
What could be the reason?
thanks

2
YateBTS / change sms welcome message
« on: February 12, 2016, 01:10:02 PM »
Hello,
in order to change the sms welcome message I've  read in this forum to change the sendGreetingfunction into nib.js
but I have two nib.js in:
/usr/src/yatebts/nib
and in
/usr/local/share/yate/scripts

should I change both?
should I re-compile yatebts after that?
thanks

3
YateBTS / nib online users not refreshed
« on: February 06, 2016, 07:23:14 AM »
Hello

Users registered on yatebts nib are not refreshed when the leave, I had to stop the mbts and start again yate with nib

4
YateBTS / Cell Reselection values C1 and C2
« on: November 01, 2015, 02:56:41 PM »
Hello,

On NIB I'havent found the following values:

cell reselection offset
penalty time
cell reselect temporary offset

in order to set-up C1  and C2 @ maximum
is there any possibility to set them?

5
YateBTS / Could not route call to '32843' [solved]
« on: May 09, 2015, 06:30:27 AM »
Hello,
I've installed all and yatebts works fine with bladeRF40
but when I try to make a IRV call to 32843 this is the result:

Could not classify call from 'TMSI007b0001', wasted 17 usec
2015-05-09_14:16:01.686657 <nib:INFO> onRoute TMSI007b0001 -> 32843
2015-05-09_14:16:01.688820 <INFO> Could not route call to '32843' in context 'default', wasted 477 usec
2015-05-09_14:16:01.689020 <ybts/1:MILD> Call rejected error='noroute' reason='No route to call target
.....

    <Cause coding="GSM-PLMN" location="LPN">noroute</Cause>
  </Message>
</CC>
-----
2015-05-09_14:16:01.690285 <ybts/1:CALL> Hangup reason='noroute' [0xb6201bb0]

and
when I run yate -sD -vvvvv -l /usr/src/yate/logfiles/yate.log
I get these errors:
.....
2015-05-09_14:15:32.470775 <mbts:MILD> miniggsn.cpp:493:miniggsn_init: could not open GGSN.Logfile.Name log file:ggsn.log
2015-05-09_14:15:32.722404 <mbts:MILD> iputils.cpp:456:ip_finddns: GGSN: DNS servers: 127.0.1.1 0.0.0.0
2015-05-09_14:15:32.723053 <mbts:MILD> iputils.cpp:363:setprocoption: Can not open file /proc/sys/net/ipv4/ip_forward error: Permission denied
2015-05-09_14:15:32.723449 <mbts:MILD> iputils.cpp:363:setprocoption: Can not open file /proc/sys/net/ipv4/ip_nonlocal_bind error: Permission denied
2015-05-09_14:15:32.724141 <mbts:MILD> iputils.cpp:311:ip_tun_open: could not create tunnel sgsntun: ioctl error: Operation not permitted
2015-05-09_14:15:32.724219 <mbts:MILD> miniggsn.cpp:627:miniggsn_init: ggsn: ERROR: Could not open tun device sgsntun
2015-05-09_14:15:32.724548 <mbts:MILD> MAC.cpp:888:macStart:   14:15:32.7,0:GGSN failed to init
....

Anyone can help me to solve this?
thanks




6
YateBTS / [Solved] YateBTS and bladeRF running problem
« on: April 11, 2015, 09:26:55 AM »
Hello guys,
I have a problem when running yate with bladeRF:
I have USB2.0
the installation of yate and yate BTS all gone OK via SVN

this is the output when i run:
 yate -Df -vvvv -l /var/log/yate.log

20150411113607.759068 <javascript:INFO> Parsed 'nib' script: /usr/local/share/yate/scripts/nib.js
20150411113607.763468 <nib:CONF> Please configure country code. See subscribers.conf or use the NIB web interface
20150411113607.765483 <NOTE> Failed to open config file '/usr/local/etc/yate/tmsidata.conf', using defaults (2: No such file or directory)
20150411113607.766009 <nib:INFO> Finished reading saved registered subscribers. Found 0 registered_subscribers.
20150411113607.766748 <nib:INFO> Checked that only NIB is enabled.
Yate engine is initialized and starting up on and-HP-Compaq-2510p-Notebook-PC
20150411113607.767043 <INFO> Creating first message dispatching thread
20150411113608.279609 <cpuload:NOTE> Updating CPU core number from 1 to 2
20150411113608.486824 <mbts:MILD> TRXManager.cpp:283:sendCommandPacket: TRX link timeout on attempt 1
20150411113609.487476 <mbts:MILD> TRXManager.cpp:283:sendCommandPacket: TRX link timeout on attempt 2
20150411113610.488483 <mbts:MILD> TRXManager.cpp:283:sendCommandPacket: TRX link timeout on attempt 3
20150411113611.489554 <mbts:MILD> TRXManager.cpp:283:sendCommandPacket: TRX link timeout on attempt 4
20150411113612.490525 <mbts:MILD> TRXManager.cpp:283:sendCommandPacket: TRX link timeout on attempt 5
20150411113612.490618 <mbts:NOTE> TRXManager.cpp:293:sendCommandPacket: lost control link to transceiver
ALERT 3075032832 13:36:12.4 TRXManager.cpp:432:powerOff: POWEROFF failed with status -1
20150411113612.491006 <mbts:WARN> TRXManager.cpp:432:powerOff: POWEROFF failed with status -1
20150411113612.595984 <mbts:NOTE> OpenBTS.cpp:145:startTransceiver: starting transceiver ./transceiver w/ 1 ARFCNs and Args:
EMERG 3074321216 13:36:12.5 OpenBTS.cpp:151:startTransceiver: cannot find ./transceiver
20150411113612.596437 <mbts:GOON> OpenBTS.cpp:151:startTransceiver: cannot find ./transceiver
EMERG 3074321216 13:36:12.5 OpenBTS.cpp:159:startTransceiver: Transceiver quit with status 256. Exiting.
20150411113612.597726 <mbts:GOON> OpenBTS.cpp:159:startTransceiver: Transceiver quit with status 256. Exiting

ybts.conf doesn't show transceiver-bladerf:

Path: string: Path to the transceiver relative to where the MBTS is started.
; Should be one of: ./transceiver-rad1 ./transceiver-usrp1 ./transceiver-uhd
; Defaults to ./transceiver.
;Path=./transceiver

but config.log produced by Yatebts's ./configure seems ok:

checking for bladeRF support using pkg-config
configure:4448: result: 1.2.1-2015.02-1-ppatrusty
configure:4483: checking libusb-1.0/libusb.h usability
configure:4483: gcc -c  -O2 -DLITTLE_ENDIAN  conftest.c >&5
configure:4483: $? = 0
configure:4483: result: yes
configure:4483: checking libusb-1.0/libusb.h presence
configure:4483: gcc -E  conftest.c
configure:4483: $? = 0
configure:4483: result: yes
configure:4483: checking for libusb-1.0/libusb.h
configure:4483: result: yes
configure:4749: creating ./config.status

I don't know how to solve this issue

Pages: [1]